3D Prints

40mm Boom Adjustable Vent

Can be installed in any velomobile with a 40mm boom. This adjustable vent allows you to better control the flow of air from the boom into the cabin. The vent can be angled in any direction or the flap can close off the majority of airflow in cooler weather. An essential addition to any velomobile.…

$42.95

Adhesive Garmin GPS mount

This simple mount allows you to attach your Garmin GPS to areas like the wheel well or dashboard. The double-sided tape provides a sufficiently firm grip.

$15.95

Apple AirTag Holder

The AirTag holders are designed to discreetly and securely hide an AirTag in your velomobile. The bar-end version comes as a set of two so your bar-ends match. The AirTag box has tabs you can run a ziptie through to attach it to areas such as the front frame, or you can add velcro to…

Select options

Buelk Magnetic Tiller Holder

Tired of your tiller falling down when you climb in your velomobile? This holder should fix the problem. Currently available for the Buelk, this involves a part that screws onto the current holder on the cockpit and another piece that clips over the brake lever. Thanks to the strength and longevity of neodynium magnets, this…

$9.99

Select options

Buelk/Milan Durable Seat Support Pad

The normal green pads have a tendency to break apart over time leaving them held together by the velcro. This pad printed from durable TPU offers the same level of support without the tendency to break down over time. The pad is heavier than the green foam pads. Therefore it is recommended to replace only…

$13.95

Bugbox Airvent for DF/DFXL Velomobiles

Designed by Velmobile Nord, this vent combines enhanced and directable ventilation with a bug screen to prevent unwanted intrusion by flying pests. An essential upgrade for your DF velomobile. Printed from durable and weather-resistant PETG.

$49.95

Garmin Varia Mount

This Garmin Varia mounts is designed for the optimal positioning of the Garmin Varia RTL 515/516. While there are several existing commercial solutions for mounting the Garmin Varia, none of them are designed for optimal positioning high on the tail. These mounts can easily be secured to the tail and provide the correct horizontal positioning…

$39.99

Select options

IQ-XL HotSpot

The ultimate hotspot to get your lights up high and bright. This version offers a mount in front for the B&M IQ-XL headlight. There will be two versions, one with a mount in the rear for the Garmin Varia, and another more aero tail where you can mount your own lights. While this is designed…

$94.99

Select options

Locking Buelk Seat Rails

Some factory-supplied Buelk seat rails have been cut with too large tolerances leading to the seat not holding firmly. This seat rail has been designed to firmly hold the seat in place. Not only does the groove have very close tolerances thanks to the precision of 3D printing, but the groove has also been designed…

$19.95

Modular Garmin GPS Mount

This modular mount allows placement of your Garmin GPS in most any position imaginable. The mount comes with double-sided adhesive for attachment, but it is recommended to use a longer bolt or glue for permanent installation. The kit includes to different length mounts, 3 different arm lengths, and the Garmin mount. Printed from stiff and…

$34.95

SnackPack Elbow Rests (set)

Made of super plush TPE, these elbow rests are the ultimate in comfort. In addition to the soft supportive surface, they also offer a compartment to hold snacks or small items. They can be attached to the walls of your velomobile using velcro.

$45.95

Soft and Durable 3D Printed Headrest

The foam headrests many velomobiles are provided with tend to break down and develop a smell over time. The goal of this headrest to provide a long-term option that will not smell. Available in two softnesses. The more firm option may provide better cushioning in the event of an accident, similar to the headrest in…

$35.95

Select options

Velomobil Nord NACA Duct

A compact NACA duct especially suited for installation in front access covers and race hoods. Printed from durable and weather-resistant PETG, optionally availble with a flexible TPU adapter gasket for installation in DF/DFXL front access covers. This duct will enhance the cooling in your velomobile. A template is included for help cutting a flap to…

Select options